meshing point中文是什么意思

• 啮合点

• "mesh"中文翻译    n. 1.网眼；筛孔；〔pl.〕网，网状物，网络；网丝； ...
• "point"中文翻译    n. 1.尖头，尖端；尖头器具；〔美国〕笔尖；接种针，雕 ...
• "end point of meshing" 中文翻译 :    啮合终止点
• "meshing" 中文翻译 :    接合；相合；啮合; 结网; 啮合
• "full meshing" 中文翻译 :    全贯通网
• "gear meshing" 中文翻译 :    齿轮啮合
• "meshing condition" 中文翻译 :    啮合条件
• "meshing depth" 中文翻译 :    啮合深度
• "meshing frame" 中文翻译 :    啮合检查结构
• "meshing gear" 中文翻译 :    啮合齿轮
• "meshing interference" 中文翻译 :    啮合干涉
• "meshing model" 中文翻译 :    啮合模型
• "meshing needle" 中文翻译 :    结网梭
• "meshing nets" 中文翻译 :    捕鲨网
• "meshing size" 中文翻译 :    网格尺寸
• "meshing solenoid" 中文翻译 :    啮合螺线管
• "meshing test" 中文翻译 :    啮合试验
• "worm meshing" 中文翻译 :    蜗杆啮合
• "advanced meshing tools" 中文翻译 :    和“高级网格工具
• "gear meshing error meter" 中文翻译 :    齿轮啮合误差测量仪
• "gear-meshing time limit" 中文翻译 :    啮合时限
• "meshing bevel gear" 中文翻译 :    啮合伞齿轮
• "tone of meshing region of engagement" 中文翻译 :    啮合区
• "a on the point of" 中文翻译 :    即将...的时候
• "at a point with" 中文翻译 :    在…之间

• The mesh points are numbered with index k in the order in which the unknowns are considered .
  网格点按所考虑的未知量以脚标k来计数。
• In surface high grinding , adapts mesh point high accuracy big area printing
  回答5 .表面中高磨削,适应网点高精度大面积印刷
• Study of load - bearing capacity for single - layer cable mesh point - supporting glass curtain
  单层索网点支式玻璃幕墙的承载性能研究
• By looking through a face on the target mesh , as if it where a window , you should be able to see every polygon on your source mesh pointing more or less in your direction
  通过察看目标网格上的一个面，比如窗户那里的面，你将可以看到在你源网格的每一个多边形或多或少的指向你的方向。
• Equipped with four - color and mesh point overprint , multi purpose ( also can be used for the single or consecutive printing for trade mark ) ; it substitutes the traditional troublesome craft , reducing the production cost greatly
  该机以印带糊、四色印刷；一机多用，可用于单张或连续商标印刷；代替传统烦琐工艺，大幅降低成本。
• Presently is equipped with the department of commercial affairs , the engineering dept , the mechanical and electrical service service department , welds shears the technological exchange department , has set up many service mesh point in hubei
  现设有商务部，工程部，机电维修服务部，焊割技术交流部，并已在湖北开办多家服务网点。
• The other is based on contour line . the way is that first editing the contour line , then saving these heights , finally depending on linear calculating middle value , thus getting the height of every mesh point , and the 3d terrain model
  另一种方法是基于等高线的方法，该方法是通过对等高线进行编辑，保存相应点的高程，再根据线性插值，得到各个网格点的高程，从而生成对应的地形模型。
• As both the meshing point and ball ' s center are on the given cylinder , a general method for developing the cam ' s profile is studied . it is proved that the profile of positive and negative transmission is unique if the face gear , the difference between face tooth number and ball number and the diameter of ball are the same . the concrete expression of meshing cam on given spatial cycloid profile , and the characteristics of the profiles are discussed
  论文的主要工作包括： 1 、根据啮合点和钢球中心轨迹均在同一圆柱面上的特点，研究了给定端齿齿廓条件下求解凸轮齿廓的一般方法；论证了在给定端齿、齿差数和钢球直径相同的条件下，正负齿差啮合齿廓的唯一性；讨论了端齿为球面摆线时，凸轮齿廓的具体表达式，并研究了该齿廓的性质。

• meshing point перевод